Development is the distance you cover with each pedal turn: development (m) = wheel circumference × chainring / cog. With a 50 x 17 and a 700 x 28C wheel (2,136 mm), you move 6.28 m per turn, or 32.8 km/h (20.4 mph) at 87 rpm. The tool also gives your gear inches, and the chart of all your gears. For your power, see the FTP calculator.
How to use it
- Enter the number of teeth on your chainring and your cog (it's stamped on them).
- Enter your cadence, in pedal revolutions per minute.
- Read your development, your speed and your gear inches.
- Open "Refine the calculation" to pick your tire size and see the table for your whole cassette: type each cog separated by a comma (11,12,13…), not just "11-34".
The method
With each pedal stroke, the chainring turns once and pulls the chain over the cog: the rear wheel therefore turns chainring / cog times. With 50 teeth up front and 17 at the back, it turns 2.94 times. Multiply by the wheel circumference and you get the development. Speed follows: development × cadence × 60 / 1,000 gives km/h.
The circumference depends on the tire. The tool uses the table Garmin publishes for setting up its bike computers: 2,096 mm for a 700 x 23C, 2,105 mm for a 700 x 25C, 2,136 mm for a 700 x 28C, 2,155 mm for a 700 x 32C, 2,200 mm for a 700 x 40C, 2,298 mm for a 29 x 2.2. On the tire sidewall, the ETRTO size (ISO 5775 standard) reads like this: 28-622 means 28 mm wide on a rim with a 622 mm diameter, the size of 700C and 29-inch wheels.
English speakers talk in gear inches: wheel diameter in inches × chainring / cog. As Sheldon Brown explains, this unit dates from before chain-driven bikes: it gave the diameter of a high-wheeler's drive wheel. The tool derives the diameter from the circumference (circumference / π).
An example
You ride a 50 x 17 on a 700 x 28C wheel (2,136 mm), at 87 rpm. Development: 2.136 × 50 / 17 = 6.28 m. Speed: 6.28 × 87 × 60 / 1,000 = 32.8 km/h. Gear inches: 78.7. With 50 and 34-tooth chainrings and an 11-34 cassette, your biggest gear (50 x 11) gives 9.71 m and 50.7 km/h, your smallest (34 x 34) 2.14 m and 11.1 km/h. With a 700 x 23C tire, the 50 x 17 would only give 6.16 m.
Limitations
Your wheel's real circumference changes with the tire brand, its pressure and your weight: the table values are benchmarks, accurate to within a few millimeters. To be precise, measure it: mark the tire and the ground, roll the bike one wheel turn while sitting on it, and enter the distance in "Your wheel circumference". The speed assumes you pedal nonstop at a steady cadence; it says nothing about effort, which depends on the gradient, the wind and your weight.
Frequently asked questions
What development for a 34 x 28?
2.59 m per pedal turn with a 700 x 28C wheel (2,136 mm circumference), or 12.4 km/h (7.7 mph) at 80 rpm.
How do you calculate a bike's development?
Multiply your wheel circumference (in meters) by the number of teeth on the chainring, then divide by the number on the cog. A 50 x 17 on a 2.136 m wheel gives 6.28 m per pedal stroke.
What speed do you get with a 50 x 11?
With a 700 x 28C wheel, a 50 x 11 gives 9.71 m of development. At 87 rpm, that's 50.7 km/h; at 100 rpm, 58.3 km/h.
What are gear inches?
It's the English-speaking way to describe a gear: wheel diameter in inches × chainring / cog. A 50 x 17 on a 700 x 28C is 78.7 gear inches. To convert to development, multiply by π and then by 0.0254: you get meters.
What's the circumference of a 700 x 28 wheel?
2,136 mm according to Garmin's bike computer table. It varies by a few millimeters depending on the tire brand and pressure: measure it if you want an accurate speed.
Why is my average speed lower than the table's?
The table assumes you pedal nonstop at the same cadence. In real life, you stop pedaling on descents and corners, and your cadence varies: so your average is lower.
Sources
- Garmin. Wheel Size and Circumference (wheel circumference table, Edge bike computer manuals).
- Brown S. Gain Ratios: A New Way to Designate Bicycle Gears. sheldonbrown.com.
- ISO 5775-1. Bicycle tyres and rims, Part 1: Tyre designations and dimensions.

